LED Bulb Labels: Lumens, Kelvin and What to Ignore
I bought eight bulbs for a flat in one order because they were the cheapest per unit and the listing said warm white. Three went in the living room and made it feel like a dentist's waiting room.

I bought eight bulbs for a flat in one order because they were the cheapest per unit and the listing said warm white. Three went in the living room and made it feel like a dentist's waiting room. Two went over the kitchen counter and were fine. One in a bedside lamp buzzed audibly on the dimmer, and two in an enclosed bathroom fitting died inside five months, which is quite a trick for a bulb rated at 25,000 hours.
Nothing on that listing was a lie. The information I needed was all printed on the box, in three numbers I had not learned to read. Bulbs are one of the few remaining products where the label tells you almost everything, and where the bestseller ranking tells you almost nothing, because what sells is whatever is cheapest per bulb in a pack of six.
Lumens replaced watts, and most people still shop in watts
Watts measure how much electricity a bulb draws. For a hundred years that doubled as a brightness figure, because every bulb converted power to light at roughly the same bad rate. LEDs broke that link, so a 9 watt LED and a 60 watt filament bulb can produce the same light. The brightness number is lumens, and it is the first thing to look for.
| Lumens | Old bulb equivalent | Where it suits |
|---|---|---|
| 250 to 450 | 25 to 40 watt | Bedside lamps, hallway wall lights, anywhere you will look at the bulb directly |
| 700 to 800 | 60 watt | The default for ceiling fittings in an average bedroom or living room |
| 1,000 to 1,100 | 75 watt | Kitchen ceilings, a single pendant in a larger room, desk lamps for close work |
| 1,500 to 1,600 | 100 watt | Utility rooms, garages, a workshop bench, high ceilings over about three metres |
One useful rule of thumb for a whole room: aim for roughly 200 lumens per square metre for living spaces and about 400 for a kitchen worktop, totalled across every fitting rather than per bulb. A 12 square metre bedroom is comfortable at around 2,400 lumens in total, which is three 800 lumen bulbs, not one 2,000 lumen monster in the middle of the ceiling. Spread beats intensity, and that single choice does more for how a room feels than any amount of spending on better bulbs.
Efficiency is the lumens divided by the watts. Decent bulbs now sit between 90 and 140 lumens per watt. If a listing boasts about energy saving but works out at 70, it is an older design being cleared out.
Kelvin is the number that decides whether you like the room
Colour temperature is printed in kelvin, and it is the specification people get wrong most often because the marketing names are not standardised. Warm white from one brand is 2,700 and from another 3,000.
At 2,700 kelvin you get the yellow light of an old filament bulb. It flatters skin, makes wood and warm paint look right, and is what nearly every living room and bedroom wants. At 3,000 it is slightly cleaner, a reasonable compromise for a bathroom or a room with grey and white surfaces. At 4,000 the light reads as neutral, almost white, and it works over a kitchen worktop or a desk while looking clinical anywhere you relax. At 5,000 and above you are into daylight bulbs, which belong in a garage, a utility room or a craft table and essentially nowhere else in a home.
Mixing temperatures in one room is the mistake that bothers people without them knowing why. A 2,700 ceiling bulb beside a 4,000 lamp looks like a fault rather than a choice, and your eye reads the cooler one as faintly green. Pick one figure per room and write it on a note in your phone, because in two years you will be replacing one bulb out of five and you will not remember.
Why I ignore the hours rating, and the daylight bulb advice
Two popular pieces of advice deserve pushing back on. The first is to buy the bulb with the longest rated life. A 25,000 hour rating refers to the LED chips, which genuinely last that long. What fails first is the driver, the small circuit in the base that converts mains power, and specifically the electrolytic capacitor inside it. Heat kills capacitors. So the rating describes a part that rarely fails while saying nothing about the part that usually does, which is why my bathroom bulbs died at five months while the identical bulbs in an open pendant are still running.
That is also why the small print about enclosed fixtures matters more than the hours figure. If a bulb says not suitable for enclosed luminaires and you put it in a sealed bathroom or ceiling fitting, expect under a year. Look for bulbs explicitly rated for enclosed use, which cost about a pound or two more, and accept that no bulb in a sealed glass dome will reach its printed life.
The second piece of advice is the one about using cool daylight bulbs indoors because they improve alertness and mood. The underlying research is about bright light exposure during the day, mostly at intensities a ceiling bulb does not come close to, and about timing rather than colour. Running 5,000 kelvin lighting in a living room at nine in the evening is the opposite of helpful if you care about sleeping. If you want the alertness effect, get more light in the morning and keep the evening warm and dim. I was sceptical of this until I swapped a home office back from 5,000 to 4,000 and stopped getting a low grade headache by late afternoon, which is one person's experience and not evidence, but it cost nothing to test.
The two specs that decide whether you keep the bulb
Colour rendering, printed as CRI or Ra, says how accurately the light shows colour against daylight. Most cheap bulbs are Ra 80, which is acceptable for a hallway and visibly flat in a kitchen, where food looks grey, or a bathroom, where makeup goes wrong. Ra 90 and above costs maybe 30 to 50 percent more per bulb and is worth it in exactly two rooms: wherever you prepare food and wherever you look in a mirror. Everywhere else, 80 is fine and I would not pay the difference.
Flicker is the other, and almost nobody prints it. Every mains LED pulses slightly; the question is how deeply. Bad drivers produce a ripple that some people perceive as eye strain or a headache without ever noticing the flicker itself. You can test it in ten seconds before the return window closes: open your phone camera, switch to slow motion video, and point it at the lit bulb. Dark rolling bands across the frame mean heavy flicker. A steady image means a decent driver. I now do this with every new bulb, and it has sent two orders back.
If any bulb will go on a dimmer, check the word dimmable on the bulb itself, not on the pack of an adjacent model. A non dimmable LED on a dimmer circuit buzzes, flickers at low settings, and shortens its own life. Older dimmers designed for filament bulbs often misbehave even with dimmable LEDs, because they need a minimum load the LEDs never reach, and the fix is a trailing edge dimmer rather than another brand of bulb. Smart bulbs sidestep this by dimming internally, and that is one of the few places a smart bulb genuinely earns the price, as our guide to choosing a smart plug that works in your home touches on for the switch side of the same problem.
What I would buy now for a two bedroom flat: 800 lumen, 2,700 kelvin, Ra 80 bulbs for the living room and bedrooms, 1,000 lumen at 4,000 kelvin and Ra 90 over the kitchen worktop, one Ra 90 bulb at 3,000 in the bathroom mirror light, and nothing in the sealed hallway fitting that is not rated for enclosed use. That is three different bulbs rather than one pack of eight, which costs a few pounds more and is the difference between a flat you like sitting in and a flat you keep adding lamps to. Pair it with proper window covering, since bright bulbs and leaky curtains make a bedroom worse together than either does alone, and our notes on blackout curtains that really block light cover that side. More label reading of this kind sits in the home section.
FAQ
Can I use a higher lumen LED in an old fitting rated for 60 watts?
Usually yes, because the rating is about heat and an LED drawing 14 watts produces far less of it than a 60 watt filament bulb. A 1,600 lumen LED in a 60 watt rated fitting is fine electrically. The limit worth respecting is the fitting's physical ventilation, since bigger LEDs run hotter at the base and a tight enclosure still shortens their life.
Why do my LED bulbs glow faintly when switched off?
A small current is leaking through the switch, which is common with illuminated switches, some dimmers and two way wiring. It is not dangerous and it costs almost nothing to run. Swapping to a bulb from a different brand sometimes stops it, since the effect depends on the driver, but the proper fix is at the switch.
Is it worth paying more for a known brand?
For driver quality and flicker, yes, and that is most of what you are paying for. The LED chips in cheap and expensive bulbs often come from the same few suppliers. Where the money goes is the circuit in the base, which is also what fails, so the premium buys lifespan rather than light.
What do I do with old LED bulbs?
They contain electronics and should not go in household waste. Most supermarkets and hardware shops that sell bulbs take them back in a small collection bin near the entrance, and council recycling centres accept them. Keep the dead ones in a bag by the door rather than in a drawer, which is where mine used to accumulate for years.
More in Home
Home
How to Choose a Tower Fan by Airflow and Noise
I bought a 42 inch tower fan in June because my desk sits under a west facing window and the room hits 29C by four in the...
Home
How to Choose Blackout Curtains That Really Block Light
The panel said one hundred percent blackout, it has four thousand reviews, and your bedroom still glows at half past five in...
Home
How to Choose a Weighted Blanket by Body Weight and Fill
You bought a weighted blanket because a thousand reviews promised deeper sleep, and now you wake up at 3 a.m.